1. #1
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6

    Trekproef: E-modulus berekenen

    ik heb een vraag ivm het berekenen van de E-modulus want ik het het klopt niet bij een waarde die ik een tabel vind.

    Geg
    materiaal Al
    diameter= 11.95 mm
    Ltot=200 mm
    L0=120 mm
    diagram =

    nu het probleem is dat we ongeveer een factor 10 er naast zitten dus het kan zijn dat ik bepaalde waarden niet exact neem die jullie nemen

    A0=(Pi*(11.92)^2)/4 = 112.16mm²
    sigma= 29000/112.16 = 258.56 N/mm²

    lengteverandering= 4 mm

    epsilon = 4/120 =0.0333
    sigma = E*epsilon
    E=sigma/epsilon ->258.56/0.033 =7756.8 N/mm²

    nu als ik in het boekje tabellenboek voor metaaltechniek de E opzoek Al staat daar tussen 60000-75000 N/mm² nu kan iemand zien waar mijn fout is.
    Last edited by thecoon; 29-01-2014 at 16:19.
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

  2. #2

    Registered
    15/12/13
    Location
    Buskot 16A Goot
    Posts
    1,278
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/0
    Quote Originally Posted by thecoon View Post
    This quote is hidden because you are ignoring this member. Show
    ik heb een vraag ivm het berekenen van de E-modulus want ik het het klopt niet bij een waarde die ik een tabel vind.

    Geg
    materiaal Al
    diameter= 11.95 mm
    Ltot=200 mm
    L0=120 mm
    diagram =

    nu het probleem is dat we ongeveer een factor 10 er naast zitten dus het kan zijn dat ik bepaalde waarden niet exact neem die jullie nemen

    A0=(Pi*(11.92)^2)/4 = 112.16mm²
    sigma= 29000/112.16 = 258.56 N/mm²

    de rek ongeveer 4 mm

    epsilon = 4/120 =0.0333
    sigma = E*epsilon
    E=sigma/epsilon ->258.56/0.033 =7756.8 N/mm²

    nu als ik in het boekje tabellenboek voor metaaltechniek de E opzoek Al staat daar tussen 60000-75000 N/mm² nu kan iemand zien waar mijn fout is.
    Als ge volgens uw begingegevens

    epsilon berekent krijgt ge 80/120 = 0.4

    Als ge dan berekent, komt ge het wel uit

    Ik denk dat uw meetresultaten fout zijn.
    no votes  

  3. #3
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6
    Quote Originally Posted by barry lyndon View Post
    This quote is hidden because you are ignoring this member. Show
    Als ge volgens uw begingegevens

    epsilon berekent krijgt ge 80/120 = 0.4

    Als ge dan berekent, komt ge het wel uit

    Ik denk dat uw meetresultaten fout zijn.
    ge die berekening is beter uitleggen ik snap het niet zo goed. gegevens hebben we gekregen dus ik heb niks berekend;

    op uw PM Ltot= totale lengt van de staaf Lo is de lengte van de versmalling

    alvast bedankt
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

  4. #4

    Registered
    15/12/13
    Location
    Buskot 16A Goot
    Posts
    1,278
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/0
    Quote Originally Posted by thecoon View Post
    This quote is hidden because you are ignoring this member. Show
    ge die berekening is beter uitleggen ik snap het niet zo goed. gegevens hebben we gekregen dus ik heb niks berekend;

    op uw PM Ltot= totale lengt van de staaf Lo is waar de staaf waar e versmalling is

    alvast bedankt
    ja, ik weet niet

    epsilon is toch de relatieve uitrekking Delta L / L0

    dus eindlengte - beginlengte over de beginlengte

    (200-120) / 120

    Denk ik eh, misschien staan uw Ltot en uw L0 voor iets geheel anders, tis lang geleden en ik ben geen expert ofzo.

    Maar das wel uw factor 10 eh, van 0.4 naar 0.0333

    Dus miss meetfout?
    no votes  

  5. #5
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6
    Quote Originally Posted by barry lyndon View Post
    This quote is hidden because you are ignoring this member. Show
    ja, ik weet niet

    epsilon is toch de relatieve uitrekking Delta L / L0

    dus eindlengte - beginlengte over de beginlengte

    (200-120) / 120

    Denk ik eh, misschien staan uw Ltot en uw L0 voor iets geheel anders, tis lang geleden en ik ben geen expert ofzo.

    Maar das wel uw factor 10 eh, van 0.4 naar 0.0333

    Dus miss meetfout?
    80/120 = 0.4 komt bij 0.66 uit
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

  6. #6
    Alexat's Avatar
    Registered
    01/03/08
    Location
    Maasmechelen - Delft(NL)
    Posts
    4,412
    iTrader
    163 (100%)
    Mentioned
    0 Post(s)
    Reputation
    0/10
    Waarom epislon niet gewoon 40/120? Er staat toch afstand +-40mm tot aan uw ultimate tensile strength?

    Laat maar: vanaf Yield is het niet meer elastisch, vergeten
    Last edited by Alexat; 29-01-2014 at 13:19.
    no votes  

  7. #7
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6
    Quote Originally Posted by Alexat View Post
    This quote is hidden because you are ignoring this member. Show
    Waarom epislon niet gewoon 40/120? Er staat toch afstand +-40mm tot aan uw ultimate tensile strength?
    E-modulus moet toch bij het lineair gebied berekend worden?
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

  8. #8

    Registered
    15/12/13
    Location
    Buskot 16A Goot
    Posts
    1,278
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/0
    Quote Originally Posted by thecoon View Post
    This quote is hidden because you are ignoring this member. Show
    E-modulus moet toch bij het lineair gebied berekend worden?
    Ja
    The Young's modulus represents the factor of proportionality in Hooke's law, relating the stress and the strain ; but this law is only valid under the assumption of an elastic or linear response. Any real material will eventually fail and break when stretched over a very large distance or with a very large force ; however, all materials exhibit Hookean behavior for small enough strains or stresses. If the range over which Hooke's law is valid is large enough compared to the typical stress that one expects to apply to the material, the material is said to be linear ; if the typical stress one would apply is outside the linear range, then the material is said to be non-linear.
    Is uw rek echt niet 4cm?
    no votes  

  9. #9
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6
    Quote Originally Posted by barry lyndon View Post
    This quote is hidden because you are ignoring this member. Show
    Ja


    Is uw rek echt niet 4cm?
    op de x-as staat volgens mij de lengteverandering
    Last edited by thecoon; 29-01-2014 at 16:20.
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

  10. #10
    Mr.Hankey's Avatar
    Registered
    30/12/10
    Location
    Otegem
    Posts
    847
    iTrader
    34 (100%)
    Mentioned
    0 Post(s)
    Reputation
    0/2
    Heeft de TS de oplossing al gevonden ?
    De beginlengte en totale lengte lijken mij eerder onrealistisch...
    no votes  

  11. #11
    thecoon's Avatar
    Registered
    20/04/11
    Location
    lhkjhi
    Posts
    1,636
    iTrader
    0
    Mentioned
    0 Post(s)
    Reputation
    0/6
    Quote Originally Posted by Mr.Hankey View Post
    This quote is hidden because you are ignoring this member. Show
    Heeft de TS de oplossing al gevonden ?
    De beginlengte en totale lengte lijken mij eerder onrealistisch...
    nee nog niet gevonden, maar de taak is afgegeven en ik weet niet of ik die ooit kan gaan inzien
    “Everyone is in favor of free speech. Hardly a day passes without its being extolled, but some people's idea of it is that they are free to say what they like, but if anyone else says anything back, that is an outrage.”

    Winston S. Churchill
    no votes  

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Log in

Log in